收藏本站
9XTend ‐ PKG ‐ E? ? Ethernet ? RF ? Modem ? – ? Product ? Manual ? v2.x4x ? [2007.01.04]
2.2.2. Setup Com Port and IP Address
The XTend-PKG-E Ethernet RF Modem supports DHCP (Dynamic Host Configuration Protocol) and
Auto IP protocols. Both protocols automatically assign IP addresses to nodes of a network.
Ethernet RF Modem Discovery
The X-CTU Software provides an easy-to-use interface that searches a local network and then dis-
plays Ethernet RF Modems found.
Discover Ethernet RF Modem, Map Com Port & Assign IP Address:
1.
2.
3.
4.
5.
6.
7.
Install both the X-CTU and the Ethernet Com Port Redirector software [See "Install Soft-
ware" section on previous page]. Re-boot the PC if prompted to do so.
Launch the X-CTU Software and select the PC Settings tab; then select the "Ethernet Com
Ports" sub-tab. [Figure 2-03]
--> After the Com Port Redirector is installed (& PC is re-booted), a "Setup Com Port" dia-
log box will appear the first time the "Ethernet Com Ports sub-tab is selected. For subse-
quent uses of the sub-tab, select the 'New IP Address' button and proceed to step 4.
Select the 'OK' button.
--> All discovered PKG-E Ethernet RF Modems will be displayed in a new "Assign IP
Address" dialog box. [Figure 2-04]
Highlight one of the discovered Ethernet RF Modems (Modem IP and Hardware Addresses
are listed in the "… discovered Ethernet Modem" section) [Figure 2-04]. If an Ethernet
Modem is not discovered, enter the IP address manually in the "Enter IP Address…" box.
Select the 'OK' button.
--> Newly assigned Ethernet Modem is listed under the "Ethernet Com Ports" sub-tab and
the first available com port is assigned to it. Note that its status is "Queued as new".
Select the 'Apply' button [located in the 'Changes' section of the "Ethernet Com Ports" sub-
tab - Figure 2-03]. Even if an Ethernet RF Modem appears in the 'Ethernet Com Port' list,
the new com port cannot be used until changes are applied and the PC is re-booted.
Re-boot the PC; then re-launch the X-CTU Software. The com port can now be used to com-
municate with the RF modem.
Figure ? 2 ‐ 03. Ethernet ? Com ? Ports ? sub ‐ tab ?????????????
(Ethernet ? Com ? Ports ? sub ‐ tab ? is ? enabled ? by ? installing ?
the ? Ethernet ? Com ? Port ? Redirector ? Software.)
Figure ? 2 ‐ 04. Assign ? IP ? Address ? dialog ? box ?
NOTE: If the Ethernet RF Modem is left in DHCP mode, it may become necessary to reconfigure a
mapped com port any time an IP address is re-assigned by the DHCP server. Dynamic addressing is
supported, but assigning a static IP address can simplify the application.
? ? 2007 ? MaxStream, ? Inc., ? Confidential ? & ? Proprietary ?‐? All ? Rights ? Reserved ?
????? 9
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
XT09-SI MODULE RF 900MHZ 1W 115K W/RPSMA
XU-A11 X-STICK 2.4GHZ USB TO XBEE
XV-8000CB :3 50.3000KHZ+/-60DPS AUTOMOTIVE GYRO SENSOR +/-60DPS
YB03WKW01-6B-JB INDICATOR PB RECT WHT LED ILLUM
YGM1 C518 THERM PTC MINI-BEAD 3MM 180C
YQD120N0006 THERMISTOR PTC OCP 6 OHM 25C
Z4D-A01 PHOTO SENSOR 7.5MM REFLECT TYPE
ZALM-301-1C-B RF TRANSCEIVER 100MW MMCX W/CONN
相关代理商/技术参数
XT09-PKI-E-NA 功能描述:射频模块 9XTend 1W Ethernet w/o accessories Intl RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R 功能描述:射频模块 9XTend 1W RS232/485 w/o accessories RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA 功能描述:射频模块 900MHz - Xtend software setable RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA-NA 功能描述:射频模块 9XTend 1W RS232/485 w/accessories no AES RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RDA 功能描述:射频模块 XTend-PKG 900 MHz IndRS-232class1/div2 RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NA 功能描述:射频模块 9XTend 1W RS232/485 w/o accessories Intl RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NL 制造商:Digi International Inc 功能描述:MODEM RF 900MHZ 9600/11
XT09-PKT-R 功能描述:MODEM RF 900MHZ RS232/485 RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:XTend™ 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125